Car Audio | DiyMobileAudio.com | Car Stereo Forum - View Profile: Lanson

Lanson has a reputation beyond reputeLanson has a reputation beyond reputeLanson has a reputation beyond reputeLanson has a reputation beyond reputeLanson has a reputation beyond reputeLanson has a reputation beyond reputeLanson has a reputation beyond reputeLanson has a reputation beyond reputeLanson has a reputation beyond reputeLanson has a reputation beyond reputeLanson has a reputation beyond repute

Lanson Lanson is offline

Enthusiast

Visitor Messages

Showing Visitor Messages 1 to 10 of 23
  1. truckguy
    02-03-2018 - permalink
    truckguy
    Hey, I was trying to find the thread you had for your Colorado when you were testing the signal coming out of the stock head unit. Can you send me a link to the some how? I’d like to check it out again. Thx!
  2. lolopicolo
    12-19-2017 - permalink
    lolopicolo
    Hi fourthmeal,

    i am writing you in regard to the JBL MS-8 discussion i found on the forum. May i ask you about the way you are fine tuning your system - do you play pinknoise/whitenoise and observe the graph of the speakerson REW? If yes how do you play it - burn it on a CD/AUX source, play it and check the mobile app?

    Many thanks in advance
    Ivan
  3. southern_eng
    09-22-2017 - permalink
    southern_eng
    The Bosch vs an Optima yellow top for $160, what would you get?
  4. southern_eng
    09-22-2017 - permalink
    southern_eng
    Hey, how is your Bosch Platinum holding up? I can get an Optima Yellow top for $150 or the Bosch for $130
  5. Wynndaddy
    01-13-2016 - permalink
    Wynndaddy
    Ok ,thanks for getting back to me . Ive got one sealed @ .6 and it sounds pretty good in a wrangler under the front pass. seat . Im really limited behind the seat of this truck but I think 1.5- 1.7 is pretty doable . Ive been talking to cherryman and Brian Fisher about doing itfor me . Fisher is only about 30min from me . Neither one of them have done this in a truck like mine . If i go that route Ill let you know how it turns out .
  6. Wynndaddy
    01-13-2016 - permalink
    Wynndaddy
    I saw one of your posts on a ported box with a SD-3 10 . I was wondering if you ever built one of these and what the results were ? Im trying to decide to go sealed or ported on these behind the seat of a ford SD crewcab .

    Man, just playing with WinISD models (not exact I know), if you put this in a ~1.7 cube box and tune way down in the 24hz range, you end up with a ruler-flat response clear out to infrasonic frequencies.

    Would make a good home theater sub as well as a good option possibly for a vehicle with poor cabin gain, I think.
  7. sbeezy
    10-01-2015 - permalink
    sbeezy
    I haven't forgotten about you bro, Just been a busy few days for me and my audio guy. will send you those prices as soon as possible. saturday should be the day I can go by the shop.
  8. cueball981
    07-29-2015 - permalink
    cueball981
    Gotcha! I'll be sure to check that one out. Thanks so much for your reply! Oh, was going to ask you too...how did you route your speaker wire to the doors? I was looking at my doors last night and noticed Ford still has that damn plug that attaches to the from the door to the car. GRRRR! Thanks!
  9. cueball981
    07-29-2015 - permalink
    cueball981
    Hello!

    Hopefully I'm not intruding. I was given your username by another member, percy072. I am about to embark on my most intensive install to date (been into car audio since I began driving at 16...40 now! LOL!). I recently purchased a 2014 Ford Fusion. I understand you're running an MS-8 (did watch your video...great install!). From previous discussions surrounding our stock Ford Sony systems, I've read that the MS-8 requires the outputs after the Sony amp to keep all the functionality of the stock amenities. In your video I notice you have the outputs from the HU going into the inputs of the MS-8. By doing so, are you retaining your SYNC chime, bluetooth, and other SYNC features?

    I am very new to these "new" cars with integrated everything, so any advice you have time to provide I'll appreciate very much!

    Chris
  10. instalher
    02-11-2015 - permalink
    instalher
    there is a guy selling an almost perfect ms-8 on here for 260 shipped... jhuston. check it out I talked to him already and he still has it..

About Me

  • About Lanson
    Location
    Overland Park, KS
    Do you work in the 12 Volt industry?
    No
  • Signature
    Special thanks to all of the industry experts that share their knowledge here on the forum
    2015 Durango R/T, MS-8, Massive N3, set of NX4's, Audiofrog GS690 and GS10, Wavecor center, Sundown SD3 10's
    2018 WRX, Helix V Eight and G-One, AD W600, AP AR3 & AR20, AE AV10H-D2

Statistics

Total Posts
Visitor Messages
Total Thanks
General Information
  • Last Activity: 2 Days Ago
  • Join Date: 01-08-2007
  • Referrals: 12

Friends

Showing Friends 1 to 8 of 8

All times are GMT -6. The time now is 04:59 AM.


Powered by vBulletin®
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.

Ad Management by RedTyger

Home | User CP | Members List | New Posts | ITrader | Faq | Post Spy